How to Clean Tile Grout in 2026: The Method That Actually Works
Short answer: Start with warm water and a stiff nylon brush. If the grout is still dingy, spread a paste of 3 parts baking soda to 1 part water, let it sit 5 to 10 minutes, scrub in small sections, and rinse. For grout that is uniformly dark or yellowed, dissolve oxygen bleach powder in very warm water, keep it damp on the grout for 10 to 15 minutes, scrub, and rinse twice. Seal the grout once it is fully dry, 24 to 48 hours later. Never use metal brushes, never mix bleach with vinegar or ammonia, and never use vinegar as a routine cleaner on cement grout or on natural stone.
If you read this guide, you will know how to pick a method by your grime and your grout type, the ladder from warm water to steam, when a stain means recoloring or regrouting, and how to seal it so it stays clean — without buying anything new.
This guide contains no affiliate links and no product picks.

The things named here — baking soda, oxygen bleach powder, a nylon grout brush, a penetrating sealer — are product types, not picks. This guide names no brands and carries no affiliate links.
Grout looks like a small problem until you kneel down and actually look at it. The tile can be spotless and the room still looks tired, because the lines between the tiles carry every spill, every shower, and every muddy shoe the room has ever seen. That is normal. Grout is cement, and cement is a sponge with a surface.
This guide is decision-first. It starts with the two answers that decide your method — what kind of grime you have, and what kind of grout it sits in — then walks the ladder from the gentlest clean to the last resort, room by room. No product picks, and nothing that asks you to scrub harder when the real problem is a worn-out sealer.
The short answer
Grout is the cement-based filler between your tiles, and most grout in most homes is cement-based — full of microscopic pores that absorb whatever sits on them: soap scum in the shower, grease in the kitchen, hard water minerals in the bathroom, and ground-in dirt on floors. The tile itself is glazed and non-porous, so it wipes clean. The grout does not, which is why a floor can look clean from standing height and dingy from knee height.
The cleaning ladder is the whole method. Start with the mildest thing that works and step up only when the grout proves it needs more. Skipping rungs wastes effort and risks the grout: acids and chlorine bleach are the two cleaners most likely to damage cement grout, and they are also the two most recommended online.
Two facts decide everything else: what kind of grout you have — sanded, unsanded, epoxy, or furan — and what kind of grime you are looking at, because soap scum, grease, mould, and mineral deposits do not respond to the same thing. Identify both before you mix anything.
Pick your method first
Every grout guide gives you one recipe. That is the first mistake, because no single recipe fits every floor. What your grout needs depends on two things: what is stuck in it, and what it is made of.
| What you see | What it usually is | Your method |
|---|---|---|
| Light gray, evenly dull, no spots | Traffic dirt and soap film | Warm water and a brush; baking soda paste if it stays dull |
| White or gray film in the shower | Soap scum and hard water deposits | Baking soda paste, then oxygen bleach if the film survives |
| Yellowed or darkened all over | Age, grease, and ground-in grime | Baking soda and hydrogen peroxide paste; oxygen bleach for the whole floor |
| Black spots in the shower | Surface mould or mildew | Baking soda and hydrogen peroxide paste; diluted bleach on white grout only, as a last resort |
| Pink or orange film | Microbial biofilm, often Serratia | Clean it, then dry the room and ventilate — it returns if the shower stays wet |
| White powdery crust | Efflorescence — salts, not mould | Diluted vinegar or a specialist remover; if it keeps returning, there is moisture underneath |
| Stains that survive every clean | Staining below the surface | Grout pen for small areas, colorant for large floors — or regrout |
If your grout is cement-based, every method in this guide applies. If it is epoxy grout, it usually cleans up with warm water and a brush, and it never needs a sealer — and never use chlorine bleach on it. If you are not sure what you have, test your chosen method in a small hidden spot first.
What grout actually is
Grout fills the joints between tiles. It keeps moisture from getting behind the tilework, holds the tiles in place, and gives a tiled surface its finished look. Grout lines are grooved and slightly rough, which makes them very good at catching and holding dirt — and dirty mop water settles into them and dries as a thin layer of grime. That is why grout needs its own attention, separate from the tile.
| Type | Where you find it | How it feels | What it needs |
|---|---|---|---|
| Sanded cement grout | Floor joints wider than an eighth of an inch | Gritty, rough to the touch | Sealed when installed; reseal yearly; the full ladder below |
| Unsanded cement grout | Wall joints narrower than an eighth of an inch | Smooth, hard | Same ladder, gentler scrubbing; it can shrink and weaken |
| Epoxy grout | Showers, kitchens, high-traffic floors | Smooth, hard, almost plastic | Warm water and a brush; no sealer; no chlorine bleach |
| Furan grout | Industrial and commercial floors | Hard, chemical-resistant | Rare in homes; non-bleach cleaners only |
The touch test is the fastest way to tell sanded from unsanded: sanded grout feels gritty because it contains sand, unsanded feels smooth. Wide joints — wider than an eighth of an inch — are almost always sanded. Epoxy grout feels smooth and hard like plastic and barely changes colour when wet, because it does not absorb water the way cement grout does. If a splash darkens the grout and it lightens again as it dries, you are looking at cement grout whose sealer has worn off.
That darkening test is also the sealer test. Drip a little water onto a dry grout line: if it beads up, the sealer is still working; if it darkens and soaks in within a minute, it is time to reseal. Grout that darkens between cleanings is usually telling you the sealer is gone, not that you need to scrub harder — and scrubbing harder on unsealed grout just pushes dirt deeper into the pores.
What are you actually cleaning?
Different rooms produce different grime. Take thirty seconds to figure out what you are dealing with, because the method follows the grime.
Floor grout. Usually a mix of soil, grease in the kitchen, and ground-in dirt from shoes. It discolours gradually and evenly, and it is the best candidate for the full ladder. Move furniture and rugs out of the way first, and sweep or vacuum before any cleaner goes down — applying cleaner to a dusty floor just moves the dirt around.
Shower grout. Soap scum, body oils, and hard water deposits, on a surface that stays wet for hours after every use. Shower grout is where mould and mildew live, and where cleaning alone is not enough: if the shower never dries, the grime comes straight back. Oxygen bleach and steam shine here, along with the drying habits — a fan, a squeegee, and a shower door left open. Kitchen grout collects grease rather than mineral deposits, and grease responds better to alkaline degreasers than to acidic cleaners — the same reason cleaning an oven starts with a degreaser rather than vinegar.
Pink or orange staining. Often a microbial biofilm, commonly Serratia, that grows where water sits. Cleaning removes it, but drying and ventilation prevent it from returning. If the pink film comes back within days of cleaning, the room is staying wet — fix the drying, not the cleaner.
Black spots. Could be mould or mildew on the surface, or a deeper moisture problem. If caulk is failing where the wall meets the tub, or water is getting behind the tile, cleaning is only a bandage. Mould that returns within days has likely penetrated below the surface — harder scrubbing will not help, and the grout needs to be removed and replaced.
White powdery crust. That is efflorescence, and it is not mould. It forms when moisture moves through cement-based grout carrying soluble salts to the surface, which crystallise as the water evaporates. It is not harmful, and diluted white vinegar or a specialist remover dissolves it on most cement grout — rinse thoroughly afterward, and never use vinegar on natural stone. If the deposits keep returning, there is a moisture source underneath the tiles, and a tiler should assess the installation or waterproofing.
Tools you need, and what not to grab
You do not need a cart full of products. Most grout cleaning can be done with items many households already have, and having the right tools makes the work noticeably easier — especially on your knees and your back.
The kit. A vacuum or broom, a bucket, a stiff-bristled nylon grout brush or an old toothbrush, a spray bottle, microfiber cloths, baking soda, degreasing dish soap for kitchen floors, and oxygen bleach powder — sodium percarbonate, often labelled as an Oxi-type cleaner. Gloves, eye protection if you are splashing anything, and knee pads or a foam kneeler for a large floor. Optional: a handheld steam cleaner with a grout detail nozzle, a grout pen or colorant, and a penetrating grout sealer with a small foam brush.
The brush matters more than the cleaner. A grout brush is made of nylon and is very stiff, which is what gets grime out of the pores. In a pinch, a toothbrush works. What does not work is a metal brush: metal bristles gouge the grout and scratch the tile, turning a cleaning job into a repair job. Go easy on stiff drill brush attachments too — they can erode older grout.
What not to grab. Metal brushes, for the reason above. Oil-based cleaning products — Murphy's Oil Soap, Pine-Sol, wax-based cleaners — which leave a sticky film inside the grout pores that attracts more dirt over time. Straight vinegar or citric acid used repeatedly on cement grout, which breaks down the grout matrix. Any acid on natural stone tile — marble, granite, travertine, slate — which will permanently etch the surface. And chlorine bleach as a routine cleaner: it is a last resort, not a maintenance product.
Method 1: warm water and a brush
This is the maintenance clean, and it is the one you should be doing most often. If your grout is already in good shape and you are keeping it that way, warm water and a brush is all it needs.
Sweep or vacuum first so you are not grinding grit into the grout. Fill a bucket with warm water, pour a little onto a small section of floor, and scrub with your brush until the dirt lifts. Work one small section at a time — about 10 to 15 square feet, roughly a small bathroom — then rinse with clean water and dry. Rinse your brush frequently, so you are not re-depositing the dirt you just lifted. On walls and counters, wipe the surface down with hot water first to loosen surface grime, then scrub the grout lines.
Two details decide whether this works. First, use fresh water: dirty mop water is the quietest cause of dirty grout, moving dirt from the tile into the grout where it dries into buildup, so change the water when it turns gray. Second, dry the grout when you finish — water sitting in grout lines accelerates future staining, so a pass with a dry microfiber cloth is part of the clean, not an extra.
If warm water and a brush leaves the grout looking the same, the grime is inside the pores rather than on the surface, and you need the next method.

Method 2: baking soda paste
If your grout is just dingy from traffic or light soap scum, start here. Baking soda is gentle, cheap, and surprisingly effective, because it is mildly abrasive — enough to lift grime out of the pores without damaging the grout.
Combine 3 parts baking soda with 1 part water to make a thick paste, adding a few drops of dish soap for greasy kitchen floors. Sweep or vacuum first, then spread the paste along the grout lines with a gloved finger or a spoon, and let it sit 5 to 10 minutes. Scrub with a nylon brush in short strokes, one small section at a time, about 10 to 15 square feet. Rinse with warm water and wipe clean with a rag or mop.
Work in small sections and rinse as you go. If you scrub the whole room before rinsing, the paste dries into a chalky mess harder to remove than the dirt was. Rinse twice — once to remove the paste, once with fresh water — because residue left in the pores attracts dirt.
Baking soda paste is the right first step for most grout because it is the gentlest thing that actually works: it handles general grime and soap scum, it is safe on coloured grout, and it costs almost nothing. If the grout is uniformly dark or yellowed, the paste will lighten it a little and then stop — that is the signal to step up, not to scrub harder.
Method 3: baking soda and hydrogen peroxide paste
When grout looks yellowed or darkened all over, the paste needs a whitening partner. Hydrogen peroxide is a mild, colour-safe bleach that brightens grout without the harsh fumes of chlorine bleach, and mixed with baking soda it handles the yellowing that plain baking soda cannot.
Mix baking soda with hydrogen peroxide — the standard 3 percent solution from the drugstore — until it forms a thick paste, and apply it directly to the grout lines. In the shower, use a paste thick enough to stay put on vertical surfaces, and pay extra attention to persistent dark spots. Leave it for 10 to 20 minutes, scrub in short strokes, then rinse thoroughly and dry the surface, because a wet surface invites mould back quickly.
Two honest notes. First, spot-test on coloured grout: hydrogen peroxide can remove colour, and a small hidden test is cheaper than a lightened stripe across your floor. Second, hydrogen peroxide and vinegar do different jobs. Peroxide is the better whitener for yellowed grout; for mould and mildew stains, vinegar — sprayed on after scrubbing and rinsing, left for 5 minutes, scrubbed again — was tested head to head against peroxide and found more effective. Use peroxide for yellowing, vinegar for mould stains, never both at once.
If the paste lifts the yellowing but the grout still looks shadowed, the grime is deeper than a paste can reach, and the next method — oxygen bleach — is the right step.

Method 4: oxygen bleach
When grout looks uniformly dark or aged, oxygen bleach is the strongest cleaner in this guide that is still safe to use regularly. It is different from chlorine bleach. Oxygen bleach — sodium percarbonate, sold as Oxi-type powder — lifts organic grime and brightens without the harsh fumes, and it is safe on coloured grout where chlorine bleach would strip the colour unevenly.
Dissolve oxygen bleach powder in very warm water following the label — a common mix is around 1 to 2 tablespoons per cup, but use your product directions. Apply generously to the grout lines, pour a little on floors and spread it with a sponge so it stays wet, and let it dwell 10 to 15 minutes. Keep it damp; a dried solution stops working. Scrub with a nylon brush, rinse thoroughly, then do one more pass with fresh water to avoid leaving residue that attracts dirt. Dry with a towel if this is a shower wall or a bathroom floor.
On vertical shower walls, liquids run off too fast to work. Mix oxygen bleach with just enough water to form a loose paste, press it into the grout lines, and lay damp paper towels over it to hold the moisture in place. That cling step is the difference between a shower clean that works and one that runs down the drain.
Chlorine bleach can whiten surface discolouration, but it does not always remove the underlying soil, it lightens coloured grout unevenly, it has no effect on epoxy grout, and residual bleach left in cement grout accelerates degradation over time. If you do use it, use it only on white or light grout, diluted 1 part bleach to 10 parts water, as a last resort rather than a routine cleaner, with the room ventilated and the grout rinsed completely afterward. Never mix it with vinegar, ammonia, or any other cleaner — the fumes are dangerous.

Method 5: steam cleaning
If you have tried scrubbing and the grout still looks shadowed, steam can push through embedded dirt, especially in textured grout. It is also handy in showers for soap scum without adding more chemicals, and it is the only method in this guide that uses no cleaner at all — just water, heated until it lifts grime out of the pores.
Start with a basic clean first, even just warm water — steam works best when it is not fighting loose surface gunk. Use a detail nozzle or grout brush attachment, move slowly along the grout lines, about 1 to 2 inches per second, and immediately wipe the loosened grime with a microfiber cloth. Rinse with clean water afterward, and use distilled water in the steamer if you can; it keeps the machine working longer. Work small areas at a time and let the area dry fully when you finish.
Steam has three watch-outs. Do not linger too long in one spot. If grout is already cracked or missing, steam can force moisture behind the tile, so fix cracked grout before you steam it. And steam can soften or strip some sealers, so plan to reseal after a steam clean if the water-drop test says the sealer is gone.
Steam is also the best answer to the scrub-free question. If your grout is well-maintained and only needs a light cleaning, steam can clean it without scrubbing. If it is not, no method works without scrubbing — any guide that promises a scrub-free deep clean on neglected grout is selling you something.
When cleaning is not enough
Sometimes grout is not dirty, it is stained. Old spills, rust-coloured minerals, or years of discolouration can penetrate so deep that cleaning only gets you partway there. That is when you stop scrubbing and switch to a cosmetic reset — or to a repair.
A grout pen is best for tight spots, small bathrooms, and rental-friendly touch-ups. Clean the grout first and let it dry fully, run the pen tip along the grout line, wipe any mistakes off the tile right away, and let it cure per the product instructions before getting it wet. A grout colorant is best for large floors, showers, dramatic colour changes, or very uneven grout colour. Deep clean first, rinse well, and let the grout dry 24 to 48 hours. Apply the colorant with a small brush in short sections, and wipe excess off the tile faces before it dries. Recolouring is slow the first time, but it can make a tired tile floor look newly installed without ripping anything out, and a darker grout hides everyday life better than a light one. For a renter, the pen is the safe choice: a surface touch-up, not a structural change.
When to stop cleaning and call a tiler. Mould that returns within a week of cleaning has penetrated the grout structure and will keep coming back until the grout is removed. Cracked, crumbling, or hollow-sounding grout — tap it with a knuckle and listen for a hollow sound, which means it has separated from the substrate underneath — needs to be replaced, not cleaned. Discolouration that does not lift after multiple attempts is permanent, and the grout needs to be replaced or recoloured. Natural stone tile needs a specialist, because cement-grout products can etch stone permanently. And uncontrollable mould may mean a hidden leak behind the tile — the longer you put off addressing it, the worse it becomes. A professional clean is also worth considering for large tiled areas, and it often costs far less than regrouting.

Sealing it so it stays clean
Sealing is not glamorous, but it is the step that makes every clean after it easier. Unsealed grout absorbs dirt and moisture faster, which means it stains faster and you scrub more often. A sealed grout line still gets dirty — it just gives the dirt nowhere to go.
Seal only after a deep clean, and only when the grout is completely dry — usually 24 to 48 hours. Sealing damp grout is the most common mistake in this whole guide: it traps moisture underneath, which can trigger mould growth, and a membrane-forming sealer over damp grout can peel or go cloudy. Apply a penetrating grout sealer with a foam brush or applicator bottle, focusing on the grout lines, wipe any sealer off the tile faces before it dries, add a second coat if the label calls for it, and let it dry 3 to 4 hours before the room goes back into use.
Choose a penetrating sealer over a membrane-forming one. A penetrating sealer soaks into the pores and creates a protective barrier without changing the appearance of the surface, and it still breathes after it soaks in. A membrane-forming sealer sits on top and is prone to peeling or going cloudy when moisture pushes to the surface. The water-drop test tells you when to reseal: drip water onto a dry grout line — if it beads, the sealer is working; if it absorbs within a minute or two, reseal. Most penetrating sealers last 1 to 3 years: shower grout often needs resealing annually, low-traffic floor grout may hold for 2 to 3 years.
Keeping it clean, room by room
A deep clean is a project; keeping grout clean is a habit, and the habits are small. Dry mop tile floors weekly so grit does not grind into the grout. Use a pH-neutral cleaner for routine mopping — alkaline or neutral cleaners maintain grout, acids slowly break it down. Wipe spills fast, especially coffee, wine, and cooking oils. Use doormats and a shoes-off zone to cut dirt at the source, and cover high-traffic areas with rugs.
The shower has its own routine, and it takes about a minute. Run the bath fan for 20 to 30 minutes after showers, squeegee the walls in 60 seconds, and leave the shower door or curtain open so air circulates and the grout dries. Hang towels so they dry quickly rather than in a heap on the floor. Mould grows where moisture lingers, and a dry shower is a clean shower — the same weekly rhythm that keeps a bathroom tidy keeps its grout clean, which is why organising the bathroom cabinet and keeping the shower dry belong in the same routine.
Frequency depends on the room. Bathroom grout benefits from monthly treatment and a full deep clean two or three times a year. Floor grout in high-traffic areas needs a weekly wipe-down and a monthly deeper scrub. Kitchen grout near the stove may need attention every two or four weeks. And remember the sealer rule: if your grout starts looking noticeably darker between cleanings, the sealer has usually worn off — reseal, and the next clean takes half the time. If your week only has ten to twenty minutes a day for cleaning, grout fits in the same rhythm as the rest of the house — one small section at a time, on the schedule in our cleaning schedule for working moms, and the deep clean lands on the room-by-room deep cleaning checklist rather than in a panicked weekend. Vacuum the floor before you start, the same way you would before cleaning a carpet — loose grit ground into grout is what dulls it fastest.
What to skip
Most grout damage is not caused by dirt. It is caused by the wrong cleaner, the wrong brush, or the wrong order. This is the list to keep on the shelf.
| Skip this | Why | Do this instead |
|---|---|---|
| Metal brushes or wire wool | Gouges grout and scratches tile | Stiff nylon grout brush or old toothbrush |
| Stiff drill brush attachments on old grout | Erodes grout, especially older grout | Hand brush, short strokes, small sections |
| Oil-based cleaners — Murphy's Oil Soap, Pine-Sol, wax | Leaves a waxy film in the pores that attracts more dirt | pH-neutral or alkaline cleaner for routine mopping |
| Vinegar or acids as a routine cleaner | Etches and weakens cement grout with repeated use | Baking soda paste for routine grime; vinegar only for targeted stains |
| Any acid on natural stone | Permanently etches marble, travertine, limestone, granite, slate | pH-neutral cleaner; a stone specialist for stains |
| Chlorine bleach on coloured grout, epoxy, or stone | Strips colour, has no effect on epoxy, etches stone | Oxygen bleach; chlorine bleach 1:10 on white grout only, last resort |
| Mixing bleach with vinegar or ammonia | Creates dangerous toxic fumes | One cleaner at a time, rinse well between attempts |
| Sealing damp grout | Traps moisture underneath, triggers mould, peels membrane sealers | Deep clean, dry 24 to 48 hours, then seal |
| Scrubbing harder when the sealer is gone | Pushes dirt deeper into unsealed pores | Water-drop test, then reseal |
| Steam on cracked or missing grout | Forces moisture behind the tile | Repair the grout first, then steam |
Verdict: Grout stays clean when you match the method to the grime, start with the mildest clean that works, and seal it once it is dry. Warm water and a brush for routine dirt, baking soda paste for dingy grout, oxygen bleach for darkened grout, steam for embedded dirt, and a grout pen when the stain is permanent. Never mix chemicals, never use metal brushes, never use acids as a routine cleaner, and never seal damp grout. The grout was never the problem. The cleaner was.
How this guide was put together
This guide was built by reading the top guides for this exact question in full, keeping only the facts two or more of them agreed on, and checking the disagreements against each other rather than picking the loudest voice. Five guides were read end to end — from Grit and Home, HomeStars, Angi, This Old House, and Lisa Bronner.
Two disagreements were settled in the open. The first is vinegar: the most recommended grout cleaner on the internet and also the one most likely to damage cement grout with repeated use, so this guide recommends it for targeted stains and not as a routine cleaner. The second is hydrogen peroxide versus vinegar for mould stains: peroxide is the better whitener for yellowed grout, and vinegar was found more effective on mould stains in head-to-head testing, so this guide splits them by job. One error was caught and left out entirely: a popular guide's touch test for identifying grout type is backwards — sanded grout feels gritty, unsanded feels smooth. No product picks appear anywhere in this guide, only types of cleaner and tool.
What to try first: Drip water on a dry grout line tonight — if it soaks in within a minute, the sealer is gone. Good looks like: grout that lightens a shade after the paste, rinses clean, and stays lighter for weeks. If it fails: the grout darkens again within days — that is the sealer, not the cleaner. Learn next: How to Clean Carpet: The Honest Guide (2026) — the carpet guide: vacuum first, blot spills from the outside in, use a simple homemade mix, and dry it within a day.
Frequently asked questions
- What is the fastest way to clean tile grout?
- Spread a paste of 3 parts baking soda to 1 part water on the grout lines, let it sit 5 to 10 minutes, scrub with a stiff nylon brush in small sections, and rinse. It handles most dingy grout in one pass, and it is the gentlest method that actually works.
- Can I clean grout without scrubbing?
- Only if the grout is already well-maintained. Steam cleaning and oxygen bleach can lift light grime without scrubbing, but on neglected grout no method works without it. Any guide that promises a scrub-free deep clean on dirty grout is selling you something.
- Is vinegar safe for grout?
- For targeted stains, yes — diluted vinegar dissolves efflorescence and helps with mould stains after scrubbing. As a routine cleaner, no: acids etch and weaken cement grout with repeated use, and vinegar must never be used on natural stone such as marble, travertine, or limestone.
- What is the white powder on my grout?
- That is efflorescence — salts carried to the surface by moisture, which crystallise as the water evaporates. It is not mould and it is not harmful. Diluted vinegar or a specialist remover dissolves it; if it keeps returning, there is a moisture source underneath the tiles.
- Why is my grout pink or orange?
- That is usually a microbial biofilm, often Serratia, that grows where water sits. Cleaning removes it, but it returns if the shower stays wet — dry the room, run the fan, and leave the shower door open after use.
- How do I clean grout in the shower?
- Use an oxygen bleach paste, thick enough to stay on vertical walls, with damp paper towels over it to hold the moisture in place for 10 to 15 minutes. Scrub, rinse, and dry — then run the fan for 20 to 30 minutes and squeegee the walls after every shower.
- How do I clean grout on the floor?
- Sweep or vacuum first, then work in sections of about 10 to 15 square feet: paste, sit, scrub, rinse, and move on. Rinse as you go, because paste left to dry turns chalky, and use fresh water — dirty mop water just moves dirt into the grout.
- Can I use bleach on grout?
- Oxygen bleach, yes — it is safe on coloured grout and has no harsh fumes. Chlorine bleach only as a last resort: diluted 1 part bleach to 10 parts water, on white or light grout only, with the room ventilated. Never on coloured grout, epoxy grout, or natural stone, and never mix it with vinegar or ammonia.
- How do I know if my grout is sanded or unsanded?
- Touch it. Sanded grout feels gritty because it contains sand; unsanded grout feels smooth. Wide joints — wider than an eighth of an inch — are almost always sanded. Epoxy grout feels smooth and hard like plastic and barely changes colour when wet.
- How often should I clean grout?
- Bathroom grout benefits from monthly treatment and a full deep clean two or three times a year. Floor grout in high-traffic areas needs a weekly wipe-down and a monthly deeper scrub. Kitchen grout near the stove may need attention every two or four weeks.
- How often should I seal grout?
- Most penetrating sealers last 1 to 3 years — shower grout often needs resealing annually, low-traffic floor grout may hold for 2 to 3 years. Test with a drop of water: if it beads, the sealer is working; if it soaks in within a minute, reseal.
- Can I use a steam cleaner on grout?
- Yes. Move slowly, about 1 to 2 inches per second, with a detail nozzle, and wipe the loosened grime away immediately. Do not steam cracked or missing grout, and do not linger in one spot — steam can force moisture behind the tile and strip some sealers.
- What if mould keeps coming back after cleaning?
- Mould that returns within days has penetrated below the grout surface — the grout needs to be removed and replaced. Check for failing caulk or a hidden leak behind the tile, because cleaning is only a bandage while water keeps getting in.
- Can I paint or recolor grout?
- Yes. A grout pen works for small areas and rental touch-ups; a colorant works for large floors and dramatic colour changes. Deep clean first, let the grout dry 24 to 48 hours, apply in short sections, and wipe excess off the tile before it dries.
- Why does my grout get dirty again so fast?
- Usually because the sealer has worn off — test with a drop of water and reseal if it soaks in. The other causes are dirty mop water, over-wet mopping, and a shower that never dries.
